What an Elevator Door Sensor Is Actually Responsible For
A door reopening device sits on the car door header or the leading edge and projects a detection field across the opening. Break that field while the doors are closing and the door operator reverses them immediately. If the obstacle appears in the last few centimetres of travel, most controllers switch to a reduced-energy nudging mode so that a hand or a trolley wheel is not crushed on first contact.
Four technologies show up on modern cars: a mechanical safety edge that only reacts on contact, an infrared light curtain with dozens of beams, a 3D time-of-flight camera that maps the whole doorway, and ultrasonic sensors still found on older or low-speed installations. Whatever the type, the sensor is a signalling device. It tells the door operator what to do. That is why a dirty lens, a polished floor, or direct sunlight on a landing can produce the classic complaint of doors that cycle open and shut for no visible reason, while the sensor itself tests fine electrically.
The 5-Inch to 27-Inch Detection Band
North American practice, and the ADA-based guidance most specifiers quote, expects the reopening device to detect a person somewhere between 5 inches (about 127 mm) and 27 inches (about 685 mm) above the floor. That is why the sensor sits at calf level on a typical automatic door: a toddler, a crawling child, a wheelchair footplate or a guide dog is well below the height of a waist-level beam.
The practical consequence is that one infrared beam mounted at 27 inches does not meet the intent of the rule. It detects an adult torso and misses almost everything else. Two beams help, but only a beam array or a camera creates a continuous vertical curtain, which is why most new light curtains use 30 to 40 beams across roughly 2 m of height. European installations under EN 81-20 lean the same way, favouring non-contact detection so the door reverses before it touches anyone.

Comparing Door Detection Technologies
Choosing between them is a site decision, not a brochure decision. Dust, light, vibration, door speed and the age of the door operator all matter more than the headline specification.
| Technology | How it detects | Typical vertical coverage | Strengths | Practical limits |
|---|---|---|---|---|
| Mechanical safety edge | Contact strip on the car door edge | Only where it is touched | Simple, immune to light and dust, low cost | Reacts after contact; discouraged for new power doors under EN 81-20 |
| Infrared light curtain | 30 to 40 infrared beams across the opening | Up to about 2 m (79 in) | Fast, non-contact, tolerant of door vibration | Beams blocked by dirt; alignment sensitive |
| 3D time-of-flight camera | Depth map of the whole doorway | Full door height, about 2 m (79 in) | Detects stationary people, wide field | Higher cost; clean optics needed; strong sunlight can interfere |
| Ultrasonic sensor | Sound echo ranging | About 1 m (39 in) | Works in dusty, dirty landings | Slower response; sensitive to airflow and temperature |

Door Zone Accuracy Is a Guide Shoe Problem
Leveling accuracy is what makes the sensor useful. If the car stops consistently at the landing, the detection field protects a predictable opening every time. If the car settles 20 mm low when the cabin is loaded, the door sill sits below the landing, passengers trip, and the sensor has to work inside a moving geometry that no amount of software can fix.
The mechanical reference behind leveling is the guiding system. Sliding guide shoes with replaceable linings and roller guide shoes define how tightly the car is held to the rail. Lining wear is the classic slow failure: clearance grows, the car drifts and swings slightly at each stop, and the door zone becomes inconsistent. Roller guide shoes such as the FKDR series are often specified on higher-speed cars because the roller set keeps friction low and the car position repeatable, but the roller itself is also a wear part that needs a replacement interval.

This is the part of the market that Ningbo Fukangda Elevator Parts Factory has served since 2006, becoming a designated supplier to Hitachi Elevator in 2008 and to Guangri Elevator in 2009, with an ISO 9001 management system introduced in 2013 and a 5,000 square metre plant built in Dongwu Town in 2015. Guide shoes, linings, rollers and locks are all wear items with a defined replacement interval, which is why buyers who plan sensor replacement also plan the mechanical side.
Locks, Interlocks and Maintenance Key Switches
A door sensor cannot stop a car from moving with its doors open; only the interlock circuit can. The interlock is a mechanical and electrical check built into the landing door lock: the car cannot start unless every door panel is locked, and if a lock opens during travel the car stops within a short, controlled distance. The triangle lock assembly is the visible half of that circuit at each landing, and its geometry has to match the door position switch and the brand interface - Hitachi, Mitsubishi, Otis, Kone, Thyssen and Modern all differ in body shape, mounting hole pattern and spring force. Because the interlock and the reopening device share the same failure consequence, maintenance teams usually service them together; the working principle behind the triangular lock explains why a stiff or deformed lock body shows up first as a door fault, not as a lock fault.
The second element is maintenance mode. When a technician puts the car into inspection or recall, the key switch at the control cabinet, base station or machine room panel must reliably open the safety circuit and prevent normal operation. Elevator power locks such as the 2801 series, control box locks and brand-specific base station locks are specified on contact rating, keyway profile and whether the switch is spring-return or latching. A worn key switch produces what looks like a sensor fault - doors that will not close, or a car that refuses to take a call - so always confirm the maintenance circuit before replacing the detection device.
A Practical Specifying Checklist
Use this sequence when ordering a replacement door sensor or a full landing door package. It keeps the electrical choice from being made before the mechanical conditions are understood.
Confirm the required detection band with the local authority having jurisdiction; do not assume a single beam is acceptable.
Match the door operator interface exactly: supply voltage, relay or transistor output, and connector type.
Size the curtain or camera field to the clear door opening height, not to the cabin height.
Check the IP rating and operating temperature range for exposed landings, freight bays and outdoor or semi-outdoor sites.
Verify the mounting brackets and cable routing, so the device survives door slam and normal vibration.
Ask which parts are individually replaceable: beam units, lenses and edge strips should not require a full assembly change.
Plan the mechanical items on the same visit - guide shoe linings, rollers and door locks wear at a similar rate to dirty optics.
Get the detection band, the operator interface and the locking circuit right and most "sensor problems" never come back. Get them wrong and the same call returns next month with a different part number on the work order.






